A process transmitter can provide much more than a measurement value. Depending on the device, a control or monitoring system may also need its identification, status, diagnostic information and configuration parameters. HART communication makes this information accessible through a defined set of commands. There are two common ways to obtain data from a HART device. […]

The Microcyber G1100 WirelessHART Smart Gateway manages a WirelessHART field network and connects wireless field-device data with host systems and data applications. The gateway provides network monitoring and configuration through a web interface. It also supports industrial communication protocols including Modbus RTU, Modbus TCP, OPC DA v2 and HART-IP, giving users different options for accessing […]

The M1100S WirelessHART Module is a wireless communication module for developing WirelessHART field devices. It is compliant with the HART 7.4 protocol and serves as the core part of a WirelessHART field device. The M1100S communicates with a customized instrument board through a TTL serial interface and control lines. Together, the module and instrument board […]

The APC3 PROFIBUS DP ASIC is a communication controller designed for the development of intelligent PROFIBUS DP slave devices. It supports the DPV0 part of the PROFIBUS DP standard and provides a processor interface, dual-port RAM, status and interrupt functions, automatic baud-rate recognition, watchdog functions, and PROFIBUS DP service processing. APC3 supports Intel and Motorola […]

The HT5700 HART modem IC is a low-power, single-chip HART communication solution for HART FSK half-duplex communication. It integrates FSK modulation and demodulation, receive filtering, signal detection, signal generation, an internal reference, and clocking functions in one device. Designed for HART circuits, the HT5700 complies with HART physical layer requirements and provides a UART interface […]

The HT1200M HART modem IC is a low-power modem chip designed for use in HART devices. It requires only a few external components to modulate and demodulate HART signals. The HT1200M supports single, half-duplex 1200 bps frequency shift keying (FSK) and uses the Bell 202 FSK standard with 1200 Hz and 2200 Hz carriers. The […]

The MC0312 Ethernet-APL built-in module is a miniaturized module developed by Microcyber that complies with 10BASE-T1L (IEEE 802.3cg). The module supports bus power supply, a communication rate of 10 Mbps, and a maximum communication distance of 1000 m. Its software protocol supports Modbus-RTU master and HART-IP slave functions. MC0312 can convert Modbus devices into HART-IP […]

The MC0307 Modbus to PA built-in module is an embedded conversion module for Modbus-RTU and PROFIBUS PA developed by Microcyber. It is part of the Microcyber M-series built-in core board modules. The MC0307 operates as a Modbus host and communicates with Modbus-RTU devices through a TTL interface. It converts data from the Modbus device into […]

Product Overview MC0313 is a compact embedded core module that converts Modbus RTU slave devices into FOUNDATION Fieldbus H1 devices. It is designed for OEM manufacturers who want to add FOUNDATION Fieldbus communication capability to their existing Modbus instruments with minimal hardware changes. As a Modbus master, the module communicates with Modbus RTU slave devices […]

The MC0310 Modbus to HART built-in module is an embedded protocol conversion module developed by Microcyber for converting Modbus RTU slave devices to HART protocol slave devices. The MC0310 is embedded in Modbus protocol input-type devices such as flow and level measurement instruments. It communicates with the Modbus device through a TTL-level interface, operates as […]

Product Overview M0313 is a compact Modbus-to-FOUNDATION Fieldbus conversion module designed for integrating Modbus RTU devices into FOUNDATION Fieldbus systems. Operating as a Modbus master, the module communicates with Modbus RTU slave devices through its serial interface and maps Modbus data to FOUNDATION Fieldbus device variables and function blocks. The M0313 is one of the […]

What This Module Does M0307 is an embedded protocol conversion module that converts Modbus RTU slave devices into PROFIBUS PA slave devices. It is designed for OEM manufacturers who want to add PROFIBUS PA communication capability to their existing Modbus instruments without redesigning the entire product. The module is embedded directly into Modbus protocol devices […]