- Producto
-
Formulario del producto
Formulario del producto
Formulario del producto
-
Manténgase al día de las últimas novedades de Microcyber Corporation. Explore nuestros comunicados de prensa, lanzamientos de nuevos productos (Foundation Fieldbus, Profibus, WirelessHART), calendarios de exposiciones internacionales y conocimientos técnicos en el sector de la automatización industrial.
Foundation Fieldbus (FF) supports two communication technologies: H1, a low-speed bus operating at 31.25 kbit/s for field instruments, and High-Speed Ethernet (HSE), operating at 100 Mbit/s for backbone networks. Physical layer testing for Foundation Fieldbus field devices primarily focuses on the H1 bus. FF H1 uses Manchester encoding, which carries clock synchronization information along with […]
A process transmitter can provide much more than a measurement value. Depending on the device, a control or monitoring system may also need its identification, status, diagnostic information and configuration parameters. HART communication makes this information accessible through a defined set of commands. There are two common ways to obtain data from a HART device. […]
The Microcyber G1100 WirelessHART Smart Gateway manages a WirelessHART field network and connects wireless field-device data with host systems and data applications. The gateway provides network monitoring and configuration through a web interface. It also supports industrial communication protocols including Modbus RTU, Modbus TCP, OPC DA v2 and HART-IP, giving users different options for accessing […]
WirelessHART is a wireless communication protocol designed for process automation applications. It adds wireless communication capabilities to HART technology while maintaining compatibility with HART devices, commands and tools. WirelessHART uses a mesh network architecture in which network devices can route messages for other devices. For engineers working with process instrumentation, WirelessHART provides a way to […]
The M1100S WirelessHART Module is a wireless communication module for developing WirelessHART field devices. It is compliant with the HART 7.4 protocol and serves as the core part of a WirelessHART field device. The M1100S communicates with a customized instrument board through a TTL serial interface and control lines. Together, the module and instrument board […]
The APC3 PROFIBUS DP ASIC is a communication controller designed for the development of intelligent PROFIBUS DP slave devices. It supports the DPV0 part of the PROFIBUS DP standard and provides a processor interface, dual-port RAM, status and interrupt functions, automatic baud-rate recognition, watchdog functions, and PROFIBUS DP service processing. APC3 supports Intel and Motorola […]
PROFIBUS DP devices are used in industrial automation for communication between PROFIBUS masters and distributed field devices. When a device manufacturer develops an intelligent PROFIBUS DP slave, the communication controller is an important part of the device architecture. A PROFIBUS DP ASIC can provide the hardware and communication functions required for implementing a PROFIBUS DP […]
As industrial automation systems become more connected, device integration has become an important part of engineering and commissioning. Field devices need to exchange information with host systems, engineering tools, and control platforms, and different integration technologies are used for different protocols and system environments. Four technologies frequently encountered in industrial automation are EDD, DTM, GSD, […]
The HT5700 HART modem IC is a low-power, single-chip HART communication solution for HART FSK half-duplex communication. It integrates FSK modulation and demodulation, receive filtering, signal detection, signal generation, an internal reference, and clocking functions in one device. Designed for HART circuits, the HT5700 complies with HART physical layer requirements and provides a UART interface […]
The HT1200M HART modem IC is a low-power modem chip designed for use in HART devices. It requires only a few external components to modulate and demodulate HART signals. The HT1200M supports single, half-duplex 1200 bps frequency shift keying (FSK) and uses the Bell 202 FSK standard with 1200 Hz and 2200 Hz carriers. The […]
The MC0312 Ethernet-APL built-in module is a miniaturized module developed by Microcyber that complies with 10BASE-T1L (IEEE 802.3cg). The module supports bus power supply, a communication rate of 10 Mbps, and a maximum communication distance of 1000 m. Its software protocol supports Modbus-RTU master and HART-IP slave functions. MC0312 can convert Modbus devices into HART-IP […]
The MC0307 Modbus to PA built-in module is an embedded conversion module for Modbus-RTU and PROFIBUS PA developed by Microcyber. It is part of the Microcyber M-series built-in core board modules. The MC0307 operates as a Modbus host and communicates with Modbus-RTU devices through a TTL interface. It converts data from the Modbus device into […]
